-
Release time: 2022-11-18
行星減速器選擇注意哪些要點 行星減速器通常由箱體、行星架、行星輪和太陽輪組成。我們在選擇減速器時主要考慮以下幾點: 精度要求高嗎？ 減速器一般分為高精度和普通精度，具體用回程間隙(側隙)的大小來表示。減速器的精度取決于減速器內齒輪的造齒精度。另外，減速機長期使用后，精度……
-
Release time: 2022-10-28
齒輪齒條在使用過程中會因為安裝或使用不規范遇到一些問題，今天在實際應用中遇到齒輪齒條在使用過程中定位精度變差，根據現場勘察情況，作出關于齒輪齒條定位精度變差原因分析。 據介紹，當負載平臺在加速減速完成后，定位精度就會出現0.4mm至0.5mm的誤差，再結合現場工作環境和齒輪安裝結構分析如下： 1.鋁型材在……
-
Release time: 2022-06-27
The core component of the planetary gearbox is the planetary gear carrier, which determines the accuracy of the gearbox, but in addition, the output shaft, sealing ring, bearing and other components also play a very important role. The planetary gearbox i
-
Release time: 2022-06-15
將一對任意螺旋角的斜齒輪安裝成其軸線既不平行又不相交，就組成了 交錯 斜齒輪傳動，所以交錯斜齒輪傳動是用來傳遞空間兩交錯軸之間運動和動力。單個齒輪就是斜齒齒輪，但由于交錯軸斜齒輪傳動和斜齒輪傳動兩軸的相對位置不同，所以傳動的特點也不一樣。接下來給大家介紹交錯軸斜齒輪傳動特點和嚙合條件。 ……
-
Release time: 2022-06-13
During the operation of the rack and pinion, in order to reduce the friction system of the rack and pinion, it needs to be lubricated. Rack and pinion lubrication mainly has two purposes, one is to promote the sliding between the tooth surfaces, that is,
-
Release time: 2022-06-10
In order to increase the rigidity of the rack in the manufacturing process, there are many treatment methods, mainly through heat treatment. Heat treatment is a process of heating or cooling a metal material in order to obtain the required metal structure
-
Release time: 2022-06-10
Common methods for gear tooth profile dressing 1. Tooth trimming Tooth trimming is a general term for edge trimming and root trimming. Generally speaking, the method of cultivating relationship is more common. Overhauling refers to conscious
-
Release time: 2022-06-09
Since the teeth of the spur gear are parallel to the axis of the gear, the same is true in each plane perpendicular to the axis. However, the gear always has a certain width, so the points and lines studied on the end face actually represent the lines and
-
Release time: 2022-06-09
The design content of the involute spur gear transmission mainly includes selecting the transmission type, determining the main parameters, and calculating the geometric dimension check of the gear transmission. When designing a gear transmission, if the
-
Release time: 2022-06-09
1. Good meshing performance. In the helical gear transmission, the contact line of the gear teeth is an oblique straight line whose angle is βb, and the gear te……
-
Release time: 2022-06-08
Introduction to the basic parameters of the gear: Addendum circle: The circle passing through the top of all teeth of the gear is called the addendum circle. Its radius is denoted by ra, and its diameter is denoted by da. Root circle: The circle pas
-
Release time: 2022-06-08
1. What does the rack and pinion module mean? The modulus of the rack and pinion is a basic parameter for calculating the geometric size, which is genera……
